Or you can contact us using the following information:

(021) 2001960 - Steenberg branch 22 Military Rd ( off main Rd above the railway line)

(021) 7055034 - Southfield Branch 118 Victoria Rd (at the bridge next to Werda butchery)

info@hireourtools.co.za

Arc Welder / Invertor 160 - 200 Amp

   Application

 

  1. For welding mild steel or steel to join two pieces of metal to each other.
  2. Used in the metal industry trade or for diy guys doing welding at home.

 


      Instructions and operating tips

  1. This is a 60% duty cycle machine which means that the machine cannot weld continuously for more than 60% of the time in 1 minute. By exceeding this welding time you stand the risk of overheating the alternator coil which could lead to serious damage and some serious additional cost to the client. 
  2. The machine is used 6min out of every 10min and then should be left to cool for 4minutes. 
  3. Any damage to the welding cables, electrode holder or earth clamp will be charged to the client 
  4. N ever leave the engine running and the electrodes connected-this leaves an open voltage circuit which can shock persons touching the bare wires
  5. The machine is used 6min out of every 10min and then should be left to cool for 4minutes. 
  6. Flammable and toxic materials should be removed from the vicinity
  7. Be sure to wear protective gear as ultra-violet rays, sparks and gasses are emitted during welding.. 

 

      Arc Welder / Invertor 160 - 200 AmpInverter Hire 

     160 or 200 amp light weight inverter to weld mild steel. The unit comes complete with cables, earth clamp, electrode holder and helmet. Welding rods are  

      available for purchase.

    Recommendations 

  1. DO NOT USE OFF A GENERATOR, you may burn out the generator and/or the inverter. We do have petrol welders for this purpose. 
  2. Any damage to the welding cables, electrode holder or earth clamp will be charged to the client. 
  3. Make sure terminals are clean and tight (Loose connections may damage the machine or cause fire). 
  4. Flammable and toxic materials should be removed from the vicinity.  
  5. Be sure to wear protective gear as ultra-violet rays, sparks and gasses are emitted during welding.  
  6. Allow 5 minute cooling period after 10 minutes use.  
  7. Do not strike the electrode onto the earth clamp a replacement fee will be charged to the client. 
  8. Only use industrial extension cable. 

   Welder Generator Petrol drivenWelder Generator Hire

 

  1.      200 amp Petrol driven to weld mild steel. The unit comes complete with cables, earth clamp, electrode holder and helmet. 

      60 %   duty lifecycle 

  1. This is a 60% duty cycle machine which means that the machine cannot weld continuously for more than 60% of the time in 1 minute 
  2. The machine cannot weld and generate power at the same time. 

   Recommendations

.  

  1. This is a 60% duty cycle machine which means that the machine cannot weld continuously for more than 60% of the time in 1 minute. By exceeding this welding time you stand the risk of overheating the alternator coil which could lead to serious damage and some serious additional cost to the client.  
  2. The machine is used 6min out of every 10min and then should be left to cool for 4minutes.  
  3. Any damage to the welding cables, electrode holder or earth clamp will be charged to the client  
  4. The machine is used 6min out of every 10min and then should be left to cool for 4minutes.  
  5. Never leave the engine running and the electrodes connected-this leaves an open voltage circuit which can shock persons touching the bare wires.  
  6. Flammable and toxic materials should be removed from the vicinity.  
  7. Be sure to wear protective gear as ultra-violet rays, sparks and gasses are emitted during welding.